Water ingress on 04 Symbol sliding windows
5 posters
The Auto-Sleeper Motorhome Owners Forum (ASOF) :: Auto-Sleeper Motorhome Forums :: Auto-Sleeper "Van Conversions" Forum
Page 1 of 1
Water ingress on 04 Symbol sliding windows
Got a problem with water ingress on the sliding window on the sliding door on my 2004 Peugeot Boxer Symbol.
On the front section of the window at the bottom of the frame is a channel containing a removable rubber moulding.
This channel appears to fill up and seep over the edge & unless I've got a chamois tucked in there, the water runs down into the door panel causing it to buckle.
The grooves & drain holes are clear, I just can't understand what's causing it.
Any ideas? anyone out there had a similar problem?
On the front section of the window at the bottom of the frame is a channel containing a removable rubber moulding.
This channel appears to fill up and seep over the edge & unless I've got a chamois tucked in there, the water runs down into the door panel causing it to buckle.
The grooves & drain holes are clear, I just can't understand what's causing it.
Any ideas? anyone out there had a similar problem?
_________________
Britons were wildcamping long before campsites
mikemelson- Donator
-
Posts : 205
Joined : 2011-06-12
Location : Poole Dorset
Auto-Sleeper Model : Symbol
Vehicle Year : 2024
Re: Water ingress on 04 Symbol sliding windows
Just had the same problem occur on my 1997 symphony and on going through past issues wondered if you resolved the problem you had with water ingress and how?
Kathys-Cottage- Member
-
Posts : 18
Joined : 2014-03-16
Member Age : 75
Location : Monmouthshire, South Wales
Auto-Sleeper Model : P/geot Boxer Symphon
Vehicle Year : 1997
Re: Water ingress on 04 Symbol sliding windows
I've found that smearing some silicone grease (available in tubes from ebay/amazon) on the rubber seal especially around the bottom and lower sides after cleaning usually stops the leak. I use a cotton bud to reach the awkward bits. Repeat annually or as and when.
Worth a try.
Hubert
Worth a try.
Hubert
Hubert- Donator
-
Posts : 191
Joined : 2014-04-27
Member Age : 70
Location : Filey, Yorkshire
Auto-Sleeper Model : Warwick Duo
Vehicle Year : 2016
Ingress
Hi
I've got a similar problem on an 02 symbol. The bottom rubber has a split in it. I get 3 or 4 mm of water on the inside channel on the door window although it does not seem to get in any further I'm not sure if its the rubber or do they all get some water in both channels?
thanks
I've got a similar problem on an 02 symbol. The bottom rubber has a split in it. I get 3 or 4 mm of water on the inside channel on the door window although it does not seem to get in any further I'm not sure if its the rubber or do they all get some water in both channels?
thanks
woodlice- Member
-
Posts : 360
Joined : 2012-10-22
Member Age : 66
Location : essex
Auto-Sleeper Model : Warick xl
Vehicle Year : 17
Ingress
Although I've no obvious water ingress, the rubber channel at the base of the sliding windows (both sides) has perished on my '99 Harmony, are these rubber bits available anywhere ?
_________________
Terry
Never walk past open doors of opportunity as you'll never know what treasures lie beyond.
newterry- Donator
-
Posts : 979
Joined : 2012-03-28
Member Age : 75
Location : J9 M27 Near Fareham
Auto-Sleeper Model : Harmony 1.9TD
Vehicle Year : 1999 reg
Similar topics
» Water ingress in VW T5 van sliding windows
» Sliding door water ingress
» Water Ingress to sliding door black trim
» Symbol Water ingress
» 1999 Symbol Water Ingress in shelf under top
» Sliding door water ingress
» Water Ingress to sliding door black trim
» Symbol Water ingress
» 1999 Symbol Water Ingress in shelf under top
The Auto-Sleeper Motorhome Owners Forum (ASOF) :: Auto-Sleeper Motorhome Forums :: Auto-Sleeper "Van Conversions" Forum
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum