The Auto-Sleeper Motorhome Owners Forum (ASOF)
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Sealant for Carver

+2
-mojo-
JandL
6 posters

Go down

Sealant for Carver Empty Sealant for Carver

Post by JandL Tue Apr 10, 2018 3:25 pm

Hi

Doing some maintenance to van, took out Carver Cascade to clean up. Wondering what best sealant to use when putting it back.

J and L
JandL
JandL
Member
Member

Male

Posts : 165
Joined : 2017-09-12
Member Age : 69
Location : Suffolk
Auto-Sleeper Model : Symphony
Vehicle Year : 1999

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by -mojo- Tue Apr 10, 2018 7:29 pm

Last one I did, I used silicone sealant - the rationale being that anything like Sikaflex is too good an adhesive, which would make it hard to remove subsequently. I was fortunate in that mine was on a Transit with Ivory paint, so I could get a silicone sealant that matched the paint almost exactly - so what little was visible on the outside was almost invisible.

I also sprayed waxoyl-type rust treatment onto the rear of the vehicle side panel below the Carver, as that area is notorious for rusting - but you have to wipe any overspray off the outside before putting the heater in, of course.
-mojo-
-mojo-
Member
Member

Male

Posts : 4566
Joined : 2012-08-04
Member Age : 24
Location : Southeast
Auto-Sleeper Model : Trooper
Vehicle Year : 2006

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by Guest Tue Apr 10, 2018 9:33 pm

Bostik Simson.

Near perfect for all of our glue needs. Use the Bostik "M" primer first
Anonymous
Guest
Guest


Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by JandL Wed Apr 11, 2018 11:11 am

Thanks for advice.
JandL
JandL
Member
Member

Male

Posts : 165
Joined : 2017-09-12
Member Age : 69
Location : Suffolk
Auto-Sleeper Model : Symphony
Vehicle Year : 1999

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by JandL Wed Apr 11, 2018 5:17 pm

Went to isolate the gas supply to the carver - 4 taps under the sink - not labelled!!

Presume 1 for heater, 1 for fridge, other 2 for cooking - is it a separate supply for hob/grill and then oven??

Trial and error to locate correct tap.
JandL
JandL
Member
Member

Male

Posts : 165
Joined : 2017-09-12
Member Age : 69
Location : Suffolk
Auto-Sleeper Model : Symphony
Vehicle Year : 1999

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by inspiredron Thu Apr 12, 2018 12:14 am

Heater, water heater, fridge and cooker? Your van could have separate heater and water heater.

_________________
Best wishes - Ron
inspiredron
inspiredron
Member
Member

Male

Posts : 3436
Joined : 2012-06-02
Member Age : 83
Location : Ellesmere, Shropshire
Auto-Sleeper Model : Lancashire
Vehicle Year : 2012

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by JandL Thu Apr 12, 2018 10:48 am

Think heater is truma electric. Is the hob, grill and oven on the the same supply??
JandL
JandL
Member
Member

Male

Posts : 165
Joined : 2017-09-12
Member Age : 69
Location : Suffolk
Auto-Sleeper Model : Symphony
Vehicle Year : 1999

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by JandL Thu Apr 12, 2018 8:04 pm

Carver replaced, water fittings checked out fine. Still not isolated gas, need to do that in morning. Still not sure why 4 gas taps - fridge yes, carver yes, cooker yes.

Heater is a Trumatic E2400 - never used it, is it both gas and electric?? Might explain 4th tap.
JandL
JandL
Member
Member

Male

Posts : 165
Joined : 2017-09-12
Member Age : 69
Location : Suffolk
Auto-Sleeper Model : Symphony
Vehicle Year : 1999

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by daisy mae Thu Apr 12, 2018 10:19 pm

Heater is 4th tap ,  mine is both gas and electric, .would think yours was too.

_________________
Be who you are and say what you feel, because those that mind don`t matter, and those who matter don`t mind.
                                                            
                                                                Dr. Seuss
daisy mae
daisy mae
Donator
Donator

Female

Posts : 6189
Joined : 2013-02-03
Location : North Norfolk
Auto-Sleeper Model : Hampshire Topaz
Vehicle Year : 2008 98

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by JandL Fri Apr 13, 2018 1:30 pm

daisy mae wrote:Heater is 4th tap ,  mine is both gas and electric, .would think yours was too.
Thanks, of course it is!! - as witnessed by the Truma vent on outside of van. Muppett moment. Off to seal the Carver then lable up the gas taps for future reference.

Steep learning curve - filled and tested water yesterday, thanks to this site did it correctly and got water flowing nicely from all taps.

John
JandL
JandL
Member
Member

Male

Posts : 165
Joined : 2017-09-12
Member Age : 69
Location : Suffolk
Auto-Sleeper Model : Symphony
Vehicle Year : 1999

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by JandL Tue Apr 17, 2018 3:54 pm

JandL wrote:Went to isolate the gas supply to the carver - 4 taps under the sink - not labelled!!

Presume 1 for heater, 1 for fridge, other 2 for cooking - is it a separate supply for hob/grill and then oven??

Trial and error to locate correct tap.
O how wrong I was. On closer inspection all taps are labelled, just a right angles to front view.

I know no silly questions, but on seems to be in the horizontal position.

So is off vertical or 180 degree turn?
JandL
JandL
Member
Member

Male

Posts : 165
Joined : 2017-09-12
Member Age : 69
Location : Suffolk
Auto-Sleeper Model : Symphony
Vehicle Year : 1999

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by bikeralw Tue Apr 17, 2018 4:20 pm

Horizontal or vertical depends on your pipe layout, as the ON position should have the tap in line with the outlet pipe.
The usual orientation is vertical for off, horizontal for on.
Al.
bikeralw
bikeralw
Donator
Donator

Male

Posts : 3888
Joined : 2013-04-22
Member Age : 73
Location : High Peak & New Zealand.
Auto-Sleeper Model : Nuevo
Vehicle Year : 2004

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by boxerman Tue Apr 17, 2018 4:22 pm

JandL wrote:

I know no silly questions, but on seems to be in the horizontal position.

So is off vertical or 180 degree turn?
Mine are vertical for off

Frank
boxerman
boxerman
Donator
Donator

Male

Posts : 4491
Joined : 2011-08-21
Member Age : 77
Location : Preston Lancs
Auto-Sleeper Model : '95 Symphony
Vehicle Year : 1995

Back to top Go down

Sealant for Carver Empty Re: Sealant for Carver

Post by JandL Tue Apr 17, 2018 4:27 pm

Thanks for replies, assumed a 90degree rotation between on/off. Forgot about pipe orientation. Mine are vertical and clearly labelled.
JandL
JandL
Member
Member

Male

Posts : 165
Joined : 2017-09-12
Member Age : 69
Location : Suffolk
Auto-Sleeper Model : Symphony
Vehicle Year : 1999

Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum