Looking for a Peugeot Owners Manual

Hi everyone,

I am a new member and I'd like to ask for some help. I bought a Peugeot Boxer Auto Sleeper Harmony from Downtide Caravans at Alby, near Cromer in Norfolk. Despite great service from the two brothers who run this company the Harmony is missing it's Peugeot Owners Manual. The Boxer is a 1995 M with a 2.0 petrol engine and 5 speed gearbox. Would anyone with the same model be willing to photocopy the Peugeot manual and post it to my home address, or as we are in the 21st Century scan it and attach it to an email? Either way I would be willing to pay your expenses or make a donation to a favourite charity.

With many thanks!

Derick Bowler

Hi Derick, welcome to ASOF.

Is it the base vehicle manual you're after, or a manual for the AS conversion part?

I have a scanned Boxer X230 base manual if that's any help?

Derick Bowler wrote:Would anyone with the same model be willing to photocopy the Peugeot manual and post it to my home address, or as we are in the 21st Century scan it and attach it to an email? 

I have sent you a PM

PB

meanchris wrote:Hi Derick, welcome to ASOF.

Is it the base vehicle manual you're after, or a manual for the AS conversion part?

I have a scanned Boxer X230 base manual if that's any help?

Hi meanchris,

Thank you for replying to my query. It is actually the base vehicle manual I am after. I have the AS Operator's manual, the one with the spiral binding, but that does not have any of the Boxer's technical details.

Kind regards.

Derick

Derick.................see above

PB

Then I have the base vehicle manual as a PDF that I can send if I have an email address.

By PM is best, if you have that facility enabled yet?

Hi, meanchris is it possible you could send me a copy of the pdf version of the Boxer's manual as well?  

I have just joined and have been looking for advice with an intermittent starting problem.  Both the AA (during roadside recovery) and a mobile mechanical have had a look and nothing has been found.  Not having a manual is not helping.  I have not got access to PM you having only just registered.

Kind regards

Tony

Hi Tony
I'm sure either meanchris or PB will send you the manual, but I doubt if it will help your starting probs.
Start a new thread and you will probably get a better response.

Frank

Hi Frank

I am a bit loathed to start a new thread yet.  I have not done enough checking myself.  I have checked for obvious breaks in the wiring, changed the crank case sensor as the most likely cause (and it is cheap) but before I start stripping out the fuel side I would like to read the manual.  It has been a few years since I worked on an engine.

Tony

What year is it?

R reg - !997 I think

OK, I was wondering whether it might be the steering lock key sensor, but I think that was only on the later X244.

Frank's the expert.

Once you have more posts you'll be able to send/receive PMs, and you can give me or Frank your email address privately to send the drawings to.

Ok.  That you for the info. I will send a PM as soon as I can.  Any idea how many posts are required?

Hi Tony,
Starting a new thread means that you will not be taking this post off topic and it will be of more use to people researching problems in the future. Look at it this way, when you are searching the archives on this forum to find clues about your starting problem, will you be searching amongst the tyre pressure threads?

Believe me, the owners handbook offers no help whatsoever to the 'getting your hands dirty' side of things. It is useful for finding out which fuse controls what sort of thing but not much else.
There is a Peter Russek manual which is not up to Haynes standards but more useful than the Pug handbook.
I gather that your van is petrol? I have a scanned copy of the Haynes Magneti Marelli 8p part of their fuel systems manual so could tell you the resistance values etc.. of the various components should you need them.

Frank

meanchris wrote:
Frank's the expert.

No he isn't

Frank

Well, it ain't me, that's for sure.

Frank thank you for the advise above.  I will do some more invest tomorrow and then start a new thread as advised. 

One thing I do know for sure, I am not the expert 

chrisk thank you very much for the link 

chrisk wrote:[You must be registered and logged in to see this link.]

I have the extended version of that on 3 DVDs which Lawrie [modelman] gave me. Do you want a copy?

Frank

Frank, PM sent