priming my water pump.
5 posters
The Auto-Sleeper Motorhome Owners Forum (ASOF) :: Auto-Sleeper Motorhome Forums :: Auto-Sleeper "Van Conversions" Forum
Page 1 of 1
priming my water pump.
For the past 2 years I hav'nt been able to prime the water pump without the assistance of a friend who removed the pump, immersed it in water, then replaced it into the van to get the water flowing.
Anymore new Ideas?
Is one of the problems caused after removing the hotwater tank pressure at the end of the season? :think_smiley_4
Anymore new Ideas?
Is one of the problems caused after removing the hotwater tank pressure at the end of the season? :think_smiley_4
photoman- New Member
-
Posts : 1
Joined : 2014-04-23
Member Age : 72
Location : leicester
Auto-Sleeper Model : auto-sleeper duetto
Re: priming my water pump.
The pump should be self priming.
I had a similar problem last year and it turned out to be the clear plastic filter housing on the pump inlet was cracked.
Fitted a replacement and it was OK after.
I had a similar problem last year and it turned out to be the clear plastic filter housing on the pump inlet was cracked.
Fitted a replacement and it was OK after.
Celticbiker- Member
-
Posts : 286
Joined : 2012-10-29
Member Age : 52
Location : South Wales
Auto-Sleeper Model : Duetto
Vehicle Year : 1998 ish
Re: priming my water pump.
Yes, self-priming. Here is a FAQ's list from Shurflo...
[You must be registered and logged in to see this link.]
[You must be registered and logged in to see this link.]
_________________
Nice to be important but more important to be nice
Paulmold- Donator
-
Posts : 26679
Joined : 2011-02-21
Member Age : 73
Location : North East Wales
Auto-Sleeper Model : Sussex Duo
Vehicle Year : 2010
Re: priming my water pump.
After the winter drain down , I recently had the same problem , it did not prime.
I took off the pump, and ran hot water over the valves/diaphragm , reassembled it , it then self primed with a lift of 5 ft. (under test). I assume that the assembly was a bit sticky , having been dry for a few months.
In the future if required , rather than bother to remove the pump , I will connect a piece of hose to the pump inlet (filter), with the pump in place, and gravity feed hot soapy water into the pump (whilst running) ,followed by a test to check it will self prime from a bucket of clean cold water.
I took off the pump, and ran hot water over the valves/diaphragm , reassembled it , it then self primed with a lift of 5 ft. (under test). I assume that the assembly was a bit sticky , having been dry for a few months.
In the future if required , rather than bother to remove the pump , I will connect a piece of hose to the pump inlet (filter), with the pump in place, and gravity feed hot soapy water into the pump (whilst running) ,followed by a test to check it will self prime from a bucket of clean cold water.
art- Member
-
Posts : 60
Joined : 2013-09-16
Member Age : 76
Location : South West
Auto-Sleeper Model : Duetto
Re: priming my water pump.
water pump is not activating on my duetto for the first time in years ,possibly seized or does it need priming ? what should i try first to test it + i don't know where its located ..any idea's peeps …much appreciated :)
flyingdoc- Member
-
Posts : 5
Joined : 2013-02-22
Member Age : 71
Location : Grays essex
Auto-Sleeper Model : Duetto
Re: priming my water pump.
Hi could you tell me where water pump is located on a 95 duetto ..cheersCelticbiker wrote:The pump should be self priming.
I had a similar problem last year and it turned out to be the clear plastic filter housing on the pump inlet was cracked.
Fitted a replacement and it was OK after.
flyingdoc- Member
-
Posts : 5
Joined : 2013-02-22
Member Age : 71
Location : Grays essex
Auto-Sleeper Model : Duetto
Re: priming my water pump.
On a 1998 Duetto, the water pump is situated behind the cupboard under the oven.
The false back of the cupboard is secured by a couple of wood screws.
The false back folds in order to remove it from the cupboard.
Run the pump and you can hear where it is to confirm that it is the same on a 1995 model.
The false back of the cupboard is secured by a couple of wood screws.
The false back folds in order to remove it from the cupboard.
Run the pump and you can hear where it is to confirm that it is the same on a 1995 model.
art- Member
-
Posts : 60
Joined : 2013-09-16
Member Age : 76
Location : South West
Auto-Sleeper Model : Duetto
Similar topics
» Priming the water pump
» Difficult water pump priming on 2014 Symbol
» Priming water system on Kingham 2017 - help!
» 2008 Warwick water heater & water pump access
» 'water heater valve' and 'water pump filter'
» Difficult water pump priming on 2014 Symbol
» Priming water system on Kingham 2017 - help!
» 2008 Warwick water heater & water pump access
» 'water heater valve' and 'water pump filter'
The Auto-Sleeper Motorhome Owners Forum (ASOF) :: Auto-Sleeper Motorhome Forums :: Auto-Sleeper "Van Conversions" Forum
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum